#Whatsize screws for ac how to#
#Whatsize screws for ac manual#
#Whatsize screws for ac free#

There are two things that determine the size of a screw: After all, while a picture frame falling off the wall would cause relatively minor damage, a shed you built in your garden falling apart could have more serious consequences. The more structural of a joint you are doing, the more important it becomes to pick the right screw. Keep in mind, though, that it’s just a rule of thumb.Īfter all, if you followed it literally, your screw would be sticking out of your workpiece anytime you tried to join two pieces of the same thickness. Of that, 1.5 inches would go through the 2×4 being attached with the remaining 3 inches would anchor the board into the main piece. It says that the anchor length of a fastener should be twice that of the workpiece you are fastening.Ĭonsidering that rule and the fact that a finished 2×4 is 1.5 x 3.5 inches, you would need a 4.5 inches long screw to attach it to another piece of wood. Before that, though, here’s a quick rule of thumb you can refer to.

However, even if that’s the case, I recommend reading through the whole article before you commit to that size.Ī Rule of Thumb for Choosing the Right Screw Sizeįurther down, I’ll get into a more systematic approach to choosing the right screw size for your application. If you are looking to join 2x4s, the best screw size to use in most cases is 2.5 inches long, gauge 8 or 9. And, while there is no one-size-fits-all formula, there are some general rules to follow and factors to consider.īefore jumping in, though, a quick answer in case you are looking for an answer to the most common situation. In this article, I’ll walk you through the process of choosing the right screw size for a wide range of situations. The second most important question is what size of fasteners to use. One of the most important questions to answer before joining two boards is what kind of fasteners to use. Handyman's World is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to. Then reposition it back into its final location, level accordingly and attach the vent duct. I would encourage you to cycle the dryer for a few minutes without clothing in it or the vent attached to verify it heats up and everything works properly.

Then plug it into the mating wall receptacle. Make sure the cable clamp is tight and holding the cord from being moved. Make sure all the screws are fairly tight. If you do have a green terminal for groud, attach it to that one. that is earth ground and you can secure that to the nearest frame member screw that is unpainted. Attach the red tagged end of your power cord to the red terminal block screw, white to white, black to black. You should see a Red, White, Black and/or Green double row terminal strip. You should see at least 3 terminals and maybe 4. Next, remove the access cover over the terminal block that is inside the dryer and where the power cord is attached.

#Whatsize screws for ac free#

The clamp prevents you from pulling the wires free from their terminations inside the dryer so don't omit this part of it. You should have or get the appropriate cable clamp feedthru for passing that cord thru and into the dryer. Next, locate the passthru opening for where the new cord goes thru the dryer. First off.position the dryer in a place that yuou can gain access to the back of the dryer.

#Whatsize screws for ac how to#

You should have a power cord that matches the 3 or 4 prong wall receptacle and it's pretty straight forward on how to connect. Good Luck and please rate 4 thumbs for the free answer. You did not give the model # so I went off of what you listed it under.

#Whatsize screws for ac manual#

This is from the manual for the Danby DCD5505W.

The dryer is now ready to be connected to the.

Re-install the cover of the junction box and.

Tighten the screws on the strain relief so that.

Attach the power cord phase conductor (red.

Tighten screw until power conductor is secure.

Attach the power cord phase conductor (black.

Tighten screw until neutral conductor is secure.

Attach the power cord neutral conductor (white.

Wire) to the ground terminal marked with the

Attach the power cord ground conductor (green.

Relief screws, do not fully tighten until electrical Sections of the strain relief and re-install strain

Insert the 4- wire supply cord through both.

Screws must remain positioned on the external Hole located on the left side of the junction box

Insert the large flange of both sections into the.

The strain relief splits into two indentical parts.

Relief clamp and remove from 4-wire supply

Loosen/remove the two screws on the strain.

Junction box located at the top rear of the dryer.

Remove the screws from the cover of the.